Understanding Plumber's Essentials for Bathtub Installation
Understanding Plumber's Essentials for Bathtub Installation
Blog Article
Have you been interested in content on Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old bathtub is readily accessible, the project can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the task as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This post will help you mount a brand-new tub in your restroom if you have currently acquired a brand-new tub and also do not need to change the plan of your previous water system pipes.
Your devices as well as product checklist must make up the following:
Planning for the Installment
Firstly, the supporting framework supplied with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its final placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost versatile tap port to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water system and inspect all joints and also new pipework for leaks and also tighten them if needed. Fill the bath tub and additionally check the overflow electrical outlet as well as the normal outlet for leaks.
Finally, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub should wait up until the tub has actually been utilized at least once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in place between the tap and the sink. Secure the tap in place with the manufacturer offered backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, leading to complications with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components and also installations. They are sold in tubes as well as cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealer can break relatively very early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Tools You Need to Install a New Bathtub . Thanks so much for spending some time to read through our content. Enjoyed our piece of writing? Please share it. Let other people check it out. We enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Protect your home, dial! Report this page